Support

Downloads

0. ZigBee Version 7.5.0.0 Firmware(Highest Version for Home Assistant ZHA)

ZigBee V7.5.0.0 Firmware

1 ZWave Version 7.23 Firmware

ZWave Ver 7.23 Firmware

2. ZigBee Version 8.1.1 Firmware

ZigBee V8.1.1 Firmware

2.1 ZigBee Version 8.1.3 Firmware, This is the latest version that could upgrade through USB,Due to Silicon Labs IDE changes since SDK 2025,there is a change on bootloader has issue to upgrade to above Z-Wave v7.24.0 and ZigBee v8.2.0,requires Zigbee2MQTT 2.5.0 and later, the v8.2.2 requires developer tool, please check below for firmwares

ZigBee V8.1.3 Firmware

3. ZWave Version 7.23.2 Firmware

ZWave Ver 7.23.2 Firmware

3.1 ZWave Version 7.23.4 Firmware

ZWave Ver 7.23.4 Firmware

Warning: All firmwares were packaged with encryption and signing and version check.

5. HA Pi4, CM4 Image

Home Assistant Pi4B image with GPIO Z-Wave 800 & ZigBee 3.0 Controller(enabled ttyAMA0 and ttyAMA4)

6. HA Pi5, CM5 Image

Home Assistant Pi5 image with GPIO Z-Wave 800 & ZigBee 3.0 Controller(enabled ttyAMA0 and ttyAMA3)

7. HomeSeer Pi4B, CM4 Image(No license)

HomeSeer Pi4B with WiFi AP image with GPIO Z-Wave 800 & ZigBee 3.0 Controller, Support Multiple Z-Wave and ZigBee controllers(enabled ttyAMA0 and ttyAMA4)(HS4.2.22.4, Zigbee Plus 1.2.1.0,Z-Wave Plus 1.1.3.0, Zigbee2MQTT 2.6.1,Z-Wave JS 15.12.0, RaspAP 3.4.1)(Configure RaspAP: http://IP:8000, User name: admin, Password: secret)

7.0 HomeSeer Pi4B, CM4 Image(No license)

HomeSeer Pi4B image with GPIO Z-Wave 800 & ZigBee 3.0 Controller(enabled ttyAMA0 and ttyAMA4)

8. HomeSeer Pi5, CM5 Image(No license)

HomeSeer Pi5 with WiFi AP image with GPIO Z-Wave 800 & ZigBee 3.0 Controller(enabled ttyAMA0 and ttyAMA3)(HS4.2.22.4, Zigbee Plus 1.2.1.0,Z-Wave Plus 1.1.3.0, Zigbee2MQTT 2.6.1,Z-Wave JS 15.6.0, RaspAP 3.4.1)(Configure RaspAP: http://IP:8000, User name: admin, Password: secret)

8.0 HomeSeer Pi5, CM5 Image(No license)

HomeSeer Pi5 image with GPIO Z-Wave 800 & ZigBee 3.0 Controller(enabled ttyAMA0 and ttyAMA3)

Warning: All images were packaged with compression, please write to microSD or SSD with PiImager or balenaEtcher.

Network Unit Configuration Tools

Network Configuration Tool(For PoE Z-Wave 800& ZigBee 3.0 Network Unit)

Network Configuration Tool

Firmware for Developer Tool

Firmware for Developer Tool(For Z-Wave v7.24.2 and ZigBee v8.2.2)

Firmware

Instructions

How to upgrade the firmware with PC Controller?

How to set up zwave-js for HomeSeer?

DYI Howto

HomeSeer Configuration

Manual for “Wise Connect Z-Wave 800 & ZigBee 3.0” on Home Assistant

Run Home Assistant with Network Unit without Docker

Configurate Network Unit and Make it Work with HomeSeer